Craftsman Garage Door Opener
Repair & Installation

🔧

Opener Repair

Motor burnout, stripped drive gears, logic board failures, limit-switch problems — we diagnose and fix all Craftsman opener issues on the spot.

🌀

Spring Replacement

A broken spring puts dangerous strain on your Craftsman motor. We replace torsion and extension springs same day with properly calibrated tension.

🔗

Cable Repair

Frayed or snapped lift cables leave your door hanging crooked and stress the opener. We replace them and re-balance the system.

📡

Remote & Keypad Programming

Lost or malfunctioning remotes, keypad resets, and myQ app pairing for Craftsman Security+ 2.0 openers — set up and tested on-site.

🏠

New Craftsman Install

Upgrading from a noisy old chain-drive unit? We install the full Craftsman lineup — belt, chain, and smart-drive models — with complete setup included.

CMXEOCG765

3/4 HP belt drive · myQ WiFi · ultra-quiet · battery backup

CMXEOCG453

1/2 HP belt drive · myQ enabled · quiet & reliable entry-level

CMXEOCG99250

Chain drive · 1/2 HP · budget-friendly · Lowe’s current model

139.53985D

Legacy Sears model · 1/2 HP chain · very common in Pueblo homes

41A5021-3A

Older 1/2 HP chain · Security+ rolling code · still widely serviced

CMXEOCG8TKV2

Smart chain drive · myQ WiFi built-in · 2-car garage workhorse

🛠️

Chamberlain-Built Know-How

Craftsman runs on Chamberlain Group hardware — we know the Security+ 2.0 protocol, myQ ecosystem, and drive-gear systems inside and out, not just generic opener repair.

📦

Legacy Parts in Stock

We stock drive gears, logic boards, remotes, and safety sensors for both current CMXEOCG models and older 139-series units — no waiting days for parts to ship.

⚡

Same-Day Service

Most Craftsman repairs in Pueblo are completed same day. Call before noon and we’ll aim to have your opener running again that afternoon.

Is Craftsman the same as Chamberlain or LiftMaster?

Yes — Craftsman openers are manufactured by The Chamberlain Group, the same company that makes Chamberlain and LiftMaster. They share the same Security+ 2.0 rolling-code protocol and myQ smart-home platform, which means parts often cross over and our technicians know the internals as well as they know any Chamberlain unit.

My Craftsman opener hums but won’t move — what’s wrong?

A humming motor that won’t drive the door almost always means a stripped plastic drive gear, a broken spring putting too much load on the motor, or a seized trolley carriage. The motor is running but can’t turn the drive. We’ll diagnose it on-site and tell you exactly which part needs replacing before we do any work.

How do I program a Craftsman remote to my opener?

Press and release the Learn button on the motor unit (usually yellow or purple on Craftsman models), then within 30 seconds press and hold the button on the remote until the opener’s light blinks or clicks. On Security+ 2.0 units the light will blink twice to confirm. If the remote still won’t sync after two attempts, the remote may need replacing or the receiver board may have an issue — give us a call.

Can I connect my Craftsman opener to myQ?

If your Craftsman opener has a yellow Learn button and was made after 2011, it likely supports myQ. Download the myQ app, press the Learn button, and follow the in-app pairing steps. Older openers without a yellow Learn button may need a myQ Home Bridge accessory. If you’re having trouble getting it to connect or stay online, we can troubleshoot or handle setup during a service visit.

How long do Craftsman garage door openers last?

A well-maintained Craftsman opener typically lasts 10–15 years. Chain-drive models need periodic lubrication and chain tension checks; belt-drive models tend to run quieter and longer with less maintenance. If your unit is over 10 years old and having issues, we’ll give you an honest assessment of whether repair or replacement makes more sense.